ZenduCam Z6 Hardware Kit Quick Setup Guide

ZenduCam Z6 Hardware Kit Quick Setup Guide



WARNING: This type of installation should be performed by a qualified individual or professional only. Working with your vehicle’s power system can be dangerous to both you and your vehicle if you do not know what you are doing! If you have any doubts, please consult a professional.


Package Contents   ————————————————————————

Installation Steps   —————————————————————————


1. Insert SIM and SD Card


In case the camera is not pre-installed with an SD and SIM cards, please follow the following step to insert the SD and SIM cards. Using the specialty screwdriver supplied with the product, unscrew the safety screw that locks the tamper proof case of the SD card and SIM card on the side of the camera.



2. Mount the camera


Attach the mounting bracket to the camera, remove the 3M adhesive tape cover and mount the camera to the windscreen. The camera should be placed as high as possible on the driver side of the vehicle. Make sure the glass is clean and dry before attaching the 3M adhesive mount to the windshield.


WARNING: Do not install the product in a location where it can obstruct the drivers field of vision.


*Refer to the user guide for detailed instructions on first time calibration and setting the camera positions



3. Insert Fuse Tap into Add-A-Fuse Kit


The hardwire kit includes an add-a-fuse that that includes a fuse tap. The fuse tap included is meant to be put in the “Fuse 1” position, while the fuse that you select from the fusebox goes into the “Fuse 2” position. (only if you are using a slot with an existing fuse). If you set them up with the wrong order, it will not feed power to the hardwire kit. 


*Select a fuse that has Ignition Power, connect it to a fuse port that has power only when the car is turned on (verify this during installation)




4. Crimp the Add-a-Fuse Kit to Connect the Hardwiring Kit Cable Together


Using needle nose pliers (or a similar crimping tool), trim off some of the rubber tubing (if necessary) to expose some wiring on your hardwiring cable. Connect that cable into the other end of the add-a-fuse (metal tube), then crimp them down together to make the connection. Once the crimping is done, use some force to tug on the add-a-fuse and wire so that nothing is loose. If everything feels tight, then the crimp is good and the connection is properly made.


5. Put the Add-a-Fuse Back into the Fuse Slot


Once everything is complete, the add-a-fuse simply needs to be put back into the slot that the fuse was taken out of. Open the vehicle fuse box and connect as follows: 

1.Red Color Wire – Ignition Power, connect it to a fuse port that has power only when the car is turned on (verify this during installation) 

2.GND – Find a reliable iron port to connect affix the ground wire to the iron port. Please note the ground wire of your hardwiring kit does not need an add-a-fuse kit and only attaches to a metal ground bolt.




6. Connect the camera


The power cable connects to the round connector located on the side of the camera. After Power is connected, run the power cable along the headliner of the car along the APillar to the power source.


Run the power cable along the headliner of the car along the A-Pillar to the power source.


    • Related Articles

    • ZenduCam Z6 Hardware Kit Quick Setup Guide

      ZenduCam Z6 Hardware Kit Quick Setup Guide WARNING: This type of installation should be performed by a qualified individual or professional only. Working with your vehicle’s power system can be dangerous to both you and your vehicle if you do not ...
    • Setting up reports on ZenduCAM

      This article explains how to set up reports on ZenduCAM, as well as the type of reports available. Steps To set up reports on ZenduCAM       1. Login to "ZenduCAM"       2. Click on "Admin"       3. Select "Scheduled reports" on the left-hand side   ...
    • User Guide on ZenduCAM

      A comprehensive user guide on ZenduCAM
    • How to export manual NVS and Media error report from ZenduCam.

      Introduction: This will guide you step-by-step procedure to export the Error report file from ZenduCam for NVS and Media error. Procedure: Login to ZenduMA. Click on the Admin tab. Click on Schedule report.  If there is no report created then click ...
    • Install ZenduCAM AD+ Series

      ZenduCAM ADPlus Installation Guide Step 1 – Specify the position to install the camera 1) The camera must be installed in the middle of the front windshield, generally in the rearview mirror area above the centerline of the front windshield. For ...